Manual J Load Calculations in New Mexico
Permit-ready Manual J, D & S reports for New Mexico HVAC contractors — built for high-desert sun, big elevation swings, and a wide climate range. We serve Albuquerque, Santa Fe, Las Cruces, Rio Rancho, and contractors across the state.
Manual J for New Mexico's Climate
New Mexico spans Climate Zones 3–5 across a huge elevation range. Las Cruces in the south runs hot, while Santa Fe sits high and cool — and intense high-desert sun shapes loads everywhere in between.
White Sands, New Mexico
High-Desert Sun
New Mexico's clear skies and intense solar radiation drive significant heat gain. We account for orientation, glazing, and shading rather than applying a flat assumption.
Valley to Mountains
From Las Cruces near 4,000 ft to Santa Fe above 7,000 ft, elevation strongly affects load. We apply elevation corrections instead of a single statewide design.
Desert Temperature Range
The high desert swings widely from day to night. We calculate for those real conditions so equipment is matched to actual peaks, not averages.
New Mexico Counties & Cities We Serve
We work with HVAC contractors across New Mexico's 33 counties — the Albuquerque metro, north-central, southern, and eastern regions.
Albuquerque Metro
Bernalillo & Sandoval counties — Albuquerque and Rio Rancho.
North-Central
Santa Fe County — Santa Fe and the high country.
Southern New Mexico
Doña Ana County — Las Cruces and the south.
Eastern New Mexico
Chaves & Lea counties — Roswell and Hobbs.
Every New Mexico Order Includes All Three
Manual J, Manual D, and Manual S are bundled in every order — no add-ons to buy. Reports are produced with ACCA-approved software and follow ACCA Manual J, D, and S methodology, formatted for submission to New Mexico building departments.
Load Calculation
Room-by-room heating and cooling loads based on New Mexico climate data, construction, insulation, windows, and occupancy.
Duct Design
Duct sizing and layout to distribute conditioned air properly throughout the building.
Equipment Selection
Equipment specifications matched to the calculated loads for the right capacity and efficiency.
New Mexico Manual J Pricing
Simple, square-footage-based pricing — every tier includes the full Manual J, D & S bundle.
$250 flat
A flat rate for smaller New Mexico homes and additions.
$0.15 / sq ft
Per-square-foot pricing for mid-size projects.
$0.17 / sq ft
Per-square-foot pricing for larger homes and light commercial.
Standard turnaround is 3-5 business days. Need it faster? 48-hour Rush adds $0.04 per sq ft, subject to current workload. Contractor+ members save 5% on every order; volume discounts of 10% (11–20 orders/yr) and 15% (21+ orders/yr) apply instead when greater — discounts don't stack. See full pricing →
Built for New Mexico Permit Submission
New Mexico jurisdictions typically require a load calculation for HVAC permits on new construction and equipment changeouts. Local requirements vary by city and county, so each report is formatted for submission to your building department, and we're glad to adjust documentation to match what your reviewer asks for.
New Mexico Manual J FAQs
Do I need a Manual J for an HVAC permit in New Mexico?
Most New Mexico jurisdictions require a Manual J load calculation for HVAC permits on new construction and equipment changeouts. Requirements vary by city and county, so we typically format every report for submission to your local building department — across the Albuquerque metro, north-central, and southern regions.
Which New Mexico cities do you serve?
We serve HVAC contractors across all 33 New Mexico counties, including Albuquerque (Bernalillo County), Rio Rancho (Sandoval County), Santa Fe (Santa Fe County), Las Cruces (Doña Ana County), and Roswell (Chaves County), plus the surrounding metro and desert regions. We're based in Boise, Idaho.
How long does a New Mexico Manual J report take?
Standard turnaround is 3-5 business days. For urgent New Mexico projects, we offer 48-hour Rush service for an additional $0.04 per sq ft on top of your base rate. Rush availability is subject to current workload.
How much does a Manual J cost in New Mexico?
Pricing starts at $250 flat for homes under 2,000 sq ft. Homes 2,000–4,000 sq ft are $0.15 per sq ft, and homes over 4,000 sq ft are $0.17 per sq ft. Every order bundles Manual J, Manual D, and Manual S together.